Hot Spot Propel bad Start Capacitor

Here’s the story.  It’s been really cold in Ontario, Canada lately.  -24 degree Celsius.  I got up on Family day morning, and thought I should check on the hot tub, as I haven’t been in it for a few days.  I went out, and noticed that the led display said “—-“.  I also checked the water, and it was only warm, almost even cold.  I turned the breaker off, then back on, and pressed the JETS button to start the pump, and get it heated back up.  The pump made a groaning / humming noise, but didn’t actually turn on.  Nothing out the jets.  I took the panels off, and didn’t see anything out of the ordinary.  Knowing that I couldn’t fix it right away, I drained the water. I googled some steps on how to properly winterize the hot tub, because with it being -24C outside, any water will freeze.

With the tub drained, and winterized, I now felt comfortable with knowing nothing is going to burst, and I started to google trying to find out why the pump wouldn’t start.  I found that there is a “Start Capacitor” that bolts to the pump, that supplies a jolt of electricity to the pump just to get it started.  I looked at the pump, and I can see it attached to the side.  Note – there is a Run Capacitor, and a Start Capacitor.  They both look the same.  Look at the below photo, and you can see both capacitors bolted to the pump.  The Start Capacitor is the smaller one.  I have a Wavemaster 9200.

061250001040.5

 

I called Pioneer Pools, in London Ontario to ask them if they have any suggestions.  They recommended I replace the whole pump for $400.  I even asked them if they’ve heard of a Start Capacitor, and the person on the phone didn’t know what it was.  They checked in the back, and didn’t have these units in stock.  Again said I need to replace the whole motor.  I’m not replacing a $400 motor, just because a $5 part if dead.

To test my theory of a bad Start Capacitor, with the breaker turned off, I wrapped a string around the pump output shaft.  I made sure the string was tight on the shaft.  I turned the breaker on, and pressed the Jets button, and heard the pump hum, but not turn on.  I pulled the string, which jumped started the pump, and it kicked on, and purred like a kitten. I turned off the breaker, and started searching for a Start Capactitor.   You can also take the cover off the capacitor, and most time you’ll see it’s gust hanging out the top.  Here’s what it looks like:

61308_300

You can use any start capacitor manufacturer you’d like, as long as it’s the same physical size, and you match the MFD, and VAC rating.  Mine was a 88-106MFD, and 330VAC.  I bought a 88-108MFD, and 330VAC.  You should match it exactly, but i’ve heard you can go over the MFD rating by 10%.  You should also stay at 330vac or over.

Once I attached this to the pump, it started up like normal.  I added water, and everything was back to normal.

I wanted to post this, in case others are searching for a solution to this problem.  I didn’t see much about the start capacitor out there.

 

2 thoughts on “Hot Spot Propel bad Start Capacitor

    • I called every electrician supply place and none of them had the proper stock and size. I found one place that had what I needed, but they only sell to actual electricians. So I called some electricians and asked them if I could use their name to buy this part. One of them said yes, and I called the supply store back and said this electrician said it was OK to use their account. Actually.. now that I think of it.. I may have purchased the capacitor from a Rheem Furnace Supply place. The Rheem furnace uses the same capacitor. So, Try calling around to some furnace places and see if they have one in stock.

Leave a Reply

Your email address will not be published.

*